Black fineliner drawing of the back of a closed envelope and a round wax seal where its folds meet.
Drawing referenceAbout reference use

Wax-seal envelope

Rule the envelope back, draw the wax seal, and stop the four folded edges where they meet it.

Everyday objectsEasyFinelinerReference practice: about 20 min
Save reference

Follow the drawing tutorial

Rule the envelope back, draw the wax seal, and stop the four folded edges where they meet it.

Start the 6-step tutorial

A small thing to tryIn pencil, redraw each diagonal from its own envelope corner and stop where it reaches the wax edge. Erase the marks inside the seal before inking.

Draw it, one step at a time

Draw a wax-seal envelope

Rule the envelope back, draw the wax seal, and stop the four folded edges where they meet it.

6 illustrated steps Full tutorial: about 20 minutes, at your pace

What you’ll need

  • HB pencil
  • Eraser
  • Ruler
  • Scrap of paper with a square corner
  • Fine black pen
  • Drawing paper

Before you start

This example is 10 cm wide and 6 cm tall. Choose where you want the envelope to sit and leave a margin all around.

  1. A graphite rectangle with upright sides and a level top and bottom.
    Drawing 1 — Rule the envelopeView larger
    Pencil

    Rule the envelope

    Instructions for Drawing 1 — Rule the envelope

    1. Make a faint dot where you want the upper-left corner. Leave at least 10 cm to its right and 6 cm below, plus a paper margin. Move the dot if the rectangle would crowd the sheet.
    2. Rule 10 cm to the right from that dot to make the top edge. Hold the ruler steady so the whole top edge stays level.
    3. Lay the long edge of a scrap of paper along your line so one square corner rests at the left end. Along the short edge, mark a dot 6 cm straight down. Slide the scrap to the right end and mark the same drop there. Both dots should be the same distance below the top edge.
    4. Join the two lower dots with the ruler. Join each lower dot straight up to the corner above it, then go over the top edge lightly so all four sides are equally clear. Both side edges should be the same height.
    Next step
  2. A wide wax seal outline near the middle of the envelope back.
    Drawing 2 — Shape the wax sealView larger
    Pencil

    Shape the wax seal

    Instructions for Drawing 2 — Shape the wax seal

    1. Start at the upper-left envelope corner and measure along the top edge. At 3.9 cm and 6.1 cm, use the scrap’s square corner to put two dots 3.1 cm down. At 5 cm along the top, mark the wax center 3.1 cm down. Put its top and bottom dots 1.1 cm above and below that center. The four outside dots give the wax seal its width and height.
    2. Starting at the left dot, curve freehand up to the top dot, down to the right dot, around the bottom dot and back to the left dot. Make the edge gently uneven like a drop of wax. Close the outline and keep all four parts roughly the same distance from its middle.
    Next step
  3. Four pencil diagonals from the envelope corners end at the edge of the wax seal.
    Drawing 3 — Join the folds to the waxView larger
    Pencil

    Join the folds to the wax

    Instructions for Drawing 3 — Join the folds to the wax

    1. Use a square paper corner at each widest dot to find a level about 4 mm above the dots. Notice where that level meets each side of the wax. From the upper-left envelope corner, curve freehand down and right to the left meeting point. From the upper-right corner, curve down and left to the right meeting point. Lift the pencil as soon as each line reaches the wax.
    2. Use the square paper corner to find the level 5 mm below the widest dots. From the lower-left envelope corner, rule up and right to that level on the left wax edge. From the lower-right corner, rule up and left to the same level on the right wax edge. Both lower seams end on the wax edge. Leave the middle of the wax clear.
    Next step
  4. Inked paper edges and the wax outline with the faint graphite around them.
    Drawing 4 — Ink the envelope and waxView larger
    Ink

    Ink the envelope and wax

    Instructions for Drawing 4 — Ink the envelope and wax

    1. Follow the four edges of the rectangle in pen. Check that the pen lines meet at all four corners of the rectangle.
    2. Follow the uneven outer wax edge in pen. Join the two ends and keep the inside of the wax open.
    3. Trace the two curved upper folds in pen. Lift the pen as soon as you reach the wax edge on either side.
    4. Trace the two ruled lower folds in pen from the bottom corners. Keep the inside of the seal clear when the two folds meet it.
    Next step
  5. A small broken ring in the wax and short hatches beside the upper-left fold.
    Drawing 5 — Add the impression and light foldsView larger
    Ink

    Add the impression and light folds

    Instructions for Drawing 5 — Add the impression and light folds

    1. Freehand most of a small circle inside the wax with two separate curves. Draw a longer arc around the upper half and down the right. Draw a shorter arc curving around the lower-left side. Leave a small gap on each side. Keep a few millimetres of open wax around the impression.
    2. Starting just below the upper-left corner, add five freehand strokes from its fold line. Slant them down and right for about 4 to 6 mm. Stop after the first 3 cm of that fold. Keep each hatch separate and leave the rest of the envelope open.
    Next step
  6. The finished envelope back has four inked folds, a round wax seal and sparse shading.
    Drawing 6 — Erase the dry pencil guidesView larger
    Cleanup

    Erase the dry pencil guides

    Instructions for Drawing 6 — Erase the dry pencil guides

    1. Fill a small patch on a scrap of the same paper with the same pen. Rub the patch gently with your eraser. If it smears, wait and test again. Once the patch stops smearing, erase the faint dots and pencil outlines beside the dry ink.
    Back to the steps

If something looks off

If the folds seem to cross the seal

In pencil, redraw each diagonal from its own envelope corner and stop where it reaches the wax edge. Erase the marks inside the seal before inking.